Security Alarms AR6000 Uživatelská příručka Strana 60
- Strana / 96
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
60 SPEKTRUM DX6 • HELICOPTER PROGRAMMING GUIDE
BINDING
Each Spektrum™ transmitter has a GUID (Globally Unique Identifier) code. Binding is the process of
programming the receiver to recognize the GUID of a single specific transmitter. Binding teaches the receiver the
specific GUID of that transmitter so that the receiver will only listen to the information from its previously bound
transmitter and ignores everything else. With over 4.2 billion GUID codes the chances of having interference
from another transmitter is virtually impossible. Fail-safe positions are set during binding and usually it is only
necessary to bind the receiver to the transmitter once. The only time it is necessary to re-bind is if you wish to
use a different transmitter or to change the fail-safe positions. Your AR6000 was bound to the transmitter during
manufacturing, however, if you wish to change to a different transmitter or change the throttle fail-safe position
the following process is necessary.
HOW TO BIND
1. With the power off, plug the bind plug into the BAT port.
2. Power on the receiver by connecting the battery to any unused port. The blue LED should be blinking.
3. Position the throttle stick in the desired fail-safe position (normally low throttle).
4. Press and hold the bind button on back of the transmitter while turning on the transmitter. The button should
flash for about 5 seconds then both LED’s (transmitter and receiver) will go solid green.
Important: Remove the bind plug after binding.
SMART FAIL-SAFE
In case of loss of signal, the throttle will go to the preset position stored during binding. The other channels will
hold last position. If the receiver is turned on before the transmitter, all channels but throttle will go to the fail-
safe positions stored during binding while the throttle will not generate a pulse so as not to affect the Electronic
Speed Control.
- 6-Channel, 10-Model Memory 1
- DSM Parkflyer and 1
- Micro Helicopter System 1
- Parkflyers Only 2
- How DSM Works 2
- Table of Contents 3
- Alternate Languages 3
- Aircraft Programming Guide 4
- Helicopter Programming Guide 5
- Warranty 5
- Model Type Selection 6
- Digital Trim Settings 10
- Servo Reversing 10
- Travel Adjustment 11
- Pitch Curve 12
- Throttle Curve 13
- User Guide 14
- 15
- Servo Specifications 16
- Charging the Transmitter 17
- Operating the Trainer System 18
- SPEKTRUM DX6 • INTRODUCTION 19
- DIGITAL TRIM LEVERS 21
- RECEIVER CHANNEL ASSIGNMENT 21
- 22
- HOW TO RANGE TEST THE SYSTEM 23
- HOW TO BIND 24
- CHAPTER 2: CONNECTIONS 25
- THROTTLE CUT 26
- NORMAL DISPLAY 27
- DIRECT TRIM ACCESS DISPLAY 27
- SYSTEM MODE 28
- FUNCTION MODE 29
- MODEL TYPE SELECTION 30
- DATA RESET 31
- DUAL RATE SWITCH SELECTION 32
- WING TYPE SELECTION 33
- FLAPERON SETUP 33
- DELTA-WING MIXING 35
- MODEL SELECTION 36
- MODEL NAME ENTRY 37
- SERVO REVERSING 38
- DUAL RATE 39
- EXPONENTIAL 40
- SUB-TRIM 41
- TRAVEL ADJUSTMENT 42
- AILERON-TO-RUDDER MIXING 43
- 4. To exit, press the 44
- ELEVATOR-TO-FLAP MIXING 45
- DIFFERENTIAL 47
- FLAP-TO-ELEVATOR OFFSET TRIM 48
- PROGRAMMABLE MIXING (A, B, C) 49
- ASSIGNING CHANNELS 50
- SWITCH SELECTION 50
- MIXING VALUE ADJUSTMENT 51
- MIXING OFFSET ADJUSTMENT 52
- ACCESSING THE OFFSET FUNCTION 52
- CHAPTER 8: Data Sheet 55
- KEY INPUT AND DISPLAY 62
- GEAR/GYRO SWITCH SELECTION 69
- IMPORTANT GYRO INFORMATION 69
- CHAPTER 7: Function Mode 72
- THROTTLE HOLD 77
- PITCH CURVE 78
- THROTTLE CURVE 80
- REVOLUTION MIXING 82
- PROGRAMMABLE MIXING (A) 83
- CCPM SWASHPLATE MIXING 88
- 89
- CCPM SERVO LOCATIONS 90
- CCPM SERVO CONNECTIONS 91
- One Year Warranty 93
- FCC Information 94
- 95SPEKTRUM DX6 • WARRANTY 95
- SPMM** #8259 96
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Security Alarms AR6000
(14 stránky)
(3 stránky)Factory-direct-hardware Hansgrohe 41528 Axor Citterio manuels
Manuels d'utilisation et guides de l'utilisateur pour Pour la maison Factory-direct-hardware Hansgrohe 41528 Axor Citterio.
Nous fournissons des manuels en pdf 1 Factory-direct-hardware Hansgrohe 41528 Axor Citterio à télécharger gratuitement par type de document : Manuel de l'utilisateur
Komentáře k této Příručce